# New Creality controller board..

**URL:** <https://forum.makewithtech.com/t/new-creality-controller-board/2822>\
**Category:** 3d Printing / Slicers / Setup / Problems\
**Created:** [December 4, 2020, 5:09pm UTC](https://forum.makewithtech.com/t/new-creality-controller-board/2822 "2020-12-04T17:09:18Z")\
**Posts on this page:** 5\
**Page:** 1

<div class="post-metadata">

**Author:** ![Vassili\_Finellis](https://yyz1.discourse-cdn.com/flex035/user_avatar/forum.makewithtech.com/vassili_finellis/32/12_2.png) [@Vassili\_Finellis](https://forum.makewithtech.com/u/Vassili_Finellis)\
**Post date:** [December 4, 2020, 5:09pm UTC](https://forum.makewithtech.com/t/new-creality-controller-board/2822/1 "2020-12-04T17:09:18Z")

</div>

> **[Creality V4.2.7 Silent Board: All You Need to Know](https://all3dp.com/2/creality-silent-board-ender-3/?utm_source=newsletter&utm_medium=email&omhide=true)**
>
> Creality's V4.2.7 silent board has been around for a couple of years. Read on to learn about the mainboard and its features!

---

<div class="post-metadata">

**Author:** ![Larry](https://avatars.discourse-cdn.com/v4/letter/l/47e85d/32.png) [@Larry](https://forum.makewithtech.com/u/Larry)\
**Post date:** [December 4, 2020, 6:10pm UTC](https://forum.makewithtech.com/t/new-creality-controller-board/2822/2 "2020-12-04T18:10:14Z")

</div>

Yep that’s been out for a while now. Some of the newier Ender 3 v2’s have them.

---

<div class="post-metadata">

**Author:** ![Ender5r](https://avatars.discourse-cdn.com/v4/letter/e/b4bc9f/32.png) [@Ender5r](https://forum.makewithtech.com/u/Ender5r)\
**Post date:** [December 4, 2020, 6:54pm UTC](https://forum.makewithtech.com/t/new-creality-controller-board/2822/3 "2020-12-04T18:54:54Z")

</div>

> [@Larry](#):
>
> Yep that’s been out for a while now. Some of the newier Ender 3 v2’s have them.

Yeah, exactly. It appears Creality’s marketing department is running a little behind… blame it on COVID 🙂

---

<div class="post-metadata">

**Author:** ![Kevin](https://avatars.discourse-cdn.com/v4/letter/k/2acd7d/32.png) [@Kevin](https://forum.makewithtech.com/u/Kevin)\
**Post date:** [December 4, 2020, 10:09pm UTC](https://forum.makewithtech.com/t/new-creality-controller-board/2822/4 "2020-12-04T22:09:15Z")

</div>

I installed the 32 bit v4.2.7 board a couple of weeks ago in my Ender3 Pro replacing the 8 bit board. I installed a BLTouch at the same time causing some headaches. Took me some time to figure out how to connect the BLTouch since there are differing versions depending on the BLTouch version and whether you want to use the adapter board or direct connect. The new firmware is has some bugs. The z-offset won’t save with the save settings and octoprint complained because the temp reporting message format is screwed up.

---

<div class="post-metadata">

**Author:** ![Ender5r](https://avatars.discourse-cdn.com/v4/letter/e/b4bc9f/32.png) [@Ender5r](https://forum.makewithtech.com/u/Ender5r)\
**Post date:** [December 4, 2020, 11:19pm UTC](https://forum.makewithtech.com/t/new-creality-controller-board/2822/5 "2020-12-04T23:19:08Z")

</div>

Have a look at the M211 command. It enables/disables software endstops. It might be preventing you from saving the Z Offset.